Acrylic is one of the most rewarding materials to laser cut. A well-cut acrylic piece has edges that look polished and professional straight off the machine, colors that are vivid and consistent, and a rigidity that makes the finished piece feel substantial in hand. But acrylic is also one of the most unforgiving materials when settings are wrong — melted edges, cracked pieces, and crazing are all common beginner mistakes that are entirely avoidable once you understand how acrylic behaves under the laser.
This guide covers everything you need to know: the difference between cast and extruded acrylic, recommended LightBurn settings for the most common thicknesses, how to diagnose and fix the most common problems, and how to flame polish cut edges to a glass-like finish.
Cast Acrylic vs Extruded Acrylic
This is the single most important distinction to understand before you buy a sheet. Cast acrylic and extruded acrylic are made differently, behave differently under the laser, and produce different results.
Cast Acrylic
Cast acrylic is made by pouring liquid acrylic monomer between two glass plates and allowing it to polymerize slowly. The result is a material with better optical clarity, higher molecular weight, and most importantly for laser users — it vaporizes cleanly when cut. Cast acrylic produces the characteristic frosted white edge that polishes brilliantly. It is the correct choice for any project where edge quality matters. Cast acrylic also engraves with a bright white frosted result that is highly legible and attractive.
Extruded Acrylic
Extruded acrylic is made by pushing acrylic through a die at high temperature. It is cheaper and more dimensionally consistent in thickness than cast acrylic, but it melts rather than vaporizes under the laser. This means cut edges tend to be smooth and clear (like glass) rather than frosted, but they are also more prone to melting and resolidifying unevenly. Extruded acrylic is harder to engrave — it produces a less visible result that can appear waxy rather than bright white. For most decorative laser projects, cast acrylic is the better choice despite the slightly higher price.
How to tell them apart: Extruded sheets usually have a paper protective backing while cast sheets often have a clear film backing. If the packaging says “XT” it is extruded; “GS” or “Cast” indicates cast acrylic. When in doubt, ask the supplier.
LightBurn Settings for Laser Cutting Acrylic
The settings below are starting points for a typical 60W CO2 laser. Always run a material test on a small piece before cutting a full sheet. Adjust speed and power in 5–10% increments until you find your optimal settings.
| Thickness | Speed (mm/s) | Power (%) | Passes | Air Assist |
|---|---|---|---|---|
| 2 mm cast acrylic | 20–25 | 60–70% | 1 | Low |
| 3 mm cast acrylic | 15–20 | 70–80% | 1 | Low |
| 5 mm cast acrylic | 10–12 | 85–95% | 1–2 | Low |
| 3 mm acrylic — engrave | 300–400 | 15–25% | 1 | Off |
Settings are for a 60W CO2 laser. Scale power up proportionally for 40W machines (multiply speed by ~0.7). Diode lasers cannot cut clear acrylic — the beam passes through rather than being absorbed.
Air Assist for Acrylic
Use low air assist when cutting acrylic, not high. High air assist cools the cut zone too aggressively, causing the acrylic to resolidify unevenly and produce rough or milky edges. Low air assist clears fumes without over-cooling the kerf. If your machine has only one air assist level, try cutting without any air assist on thin acrylic (2–3 mm) and compare edge quality.
Common Problems and Fixes
Melted or Rough Edges
Cause: Speed too slow or power too high, causing excessive heat buildup in the kerf. Also caused by high air assist cooling the melt unevenly.
Fix: Increase speed by 10–15% or reduce power by 5%. Switch to low air assist. Ensure you are using cast acrylic rather than extruded.
Incomplete Cuts (Material Not Falling Free)
Cause: Speed too fast or power too low. Also caused by dirty or misaligned optics, or material that is actually thicker than labeled.
Fix: Measure material thickness with calipers. Clean the focus lens. Reduce speed by 10% or add a second pass at lower power (30–40%) to finish the cut without re-melting the edges.
Crazing (Fine Cracks in the Material)
Cause: Thermal stress from too much heat applied too quickly. Common when power is very high and speed very low.
Fix: Increase speed, reduce power, and use multiple passes. Crazing is more common in extruded acrylic — switch to cast if the problem persists.
Protective Film Melting to the Surface
Cause: Cutting through the protective plastic film at too slow a speed.
Fix: Remove the protective film before cutting, or use paper masking tape instead of the plastic film. Paper tape burns cleanly and protects the surface from smoke staining.
Flame Polishing Acrylic Edges
Laser-cut edges on cast acrylic are already frosted and attractive, but flame polishing transforms them into a crystal-clear glass-like finish. The technique uses a small butane or hydrogen torch to briefly melt the surface of the cut edge, which flows and resolidifies smooth and transparent.
- Hold the torch 5–10 cm from the edge and move at a steady pace of about 2 cm per second. The flame should be small and blue, not yellow and sooty.
- Never stop moving while the flame is on the surface. Dwelling causes bubbling and permanent damage.
- Do not flame polish engraved areas — the heat fills in the engraved texture and makes it disappear.
- Always work in a well-ventilated area. Acrylic fumes are irritating and potentially harmful in enclosed spaces.
Best Designs for Acrylic
Not all laser cut designs suit acrylic equally. The best acrylic projects take advantage of the material’s unique properties: polished translucent edges, available in vivid colors, and a rigidity that holds detail well.
- Earrings and jewelry — 2–3 mm acrylic in bold colors is the dominant material for laser cut statement earrings. Lightweight, colorful, and fast to produce in quantity.
- Keychains — small, fast to cut, easy to sell. Mirror acrylic in gold and silver is especially popular.
- LED illuminated signs — clear or frosted acrylic with edge-lit LED creates the classic “neon” sign effect at a fraction of the cost of real neon.
- Geometric home decor — wall art, decorative panels, and geometric shapes in colored acrylic make striking modern home decor items.
Download Free Acrylic DXF Files
FreeLaserFile hosts hundreds of free DXF files optimized for acrylic cutting — earrings, keychains, decorative panels, clocks, and LED sign templates. Each file page notes the recommended material and thickness. Browse all free designs and filter by acrylic to find the right project for your machine.
Download Free Acrylic Laser Files
Browse our collection of free DXF and SVG files optimized for acrylic laser cutting. Earrings, keychains, LED signs, geometric decor, and more — all tested and ready to cut.